New Construction Electrical in Culver City, CA

Buzo Electric Co provides new construction electrical in Culver City, CA for custom homes, full renovations, and commercial build-outs. We are a C-10 electrical contractor and integrator: the same firm that runs your 400A service also programs your Control4 or Josh AI system. Architects, GCs, and interior designers bring us in at design-build, and homeowners get one licensed point of responsibility from load calculation through trim-out. If you are planning a ground-up build or a full renovation in Culver City, contact us to review the plans and scope the electrical and integration package together.

Our New Construction Electrical Services in Culver City, CA

Our new construction electrical work in Culver City, CA covers the full scope of a high-end build, from service entrance to the last keypad.

• Design-build electrical for new and custom homes. We work with the architect and GC from the drawing stage: load calculations, panel schedules, circuit layout, rough-in, and trim-out, coordinated with the rest of the trades.
• Electrical service upgrades: 200A and 400A panels. A custom home with EV charging, standby power, and a head end often needs a 400A service. We size it from the load calculation, not a guess, and install Span smart panels and subpanels where the design calls for them.
• Lutron lighting control and motorized shades. Lighting control is engineered into the plan, not added after. We design the keypad layout, program each scene, and commission the shades as part of the same contract.
• Control4 and Josh AI whole-home automation. Structured wiring, rack build, head end, programming, and ongoing support, all from the firm that pulled the wire at rough-in.
• Home theater, media rooms, and whole-home audio and video. Low voltage is planned alongside the line voltage, so speaker locations, display power, and rack cooling are in the walls before drywall.
• Generac standby power and EV charging. Whole-house Generac standby generators with an automatic transfer switch, plus Level 2 chargers and Tesla Wall Connector installation, sized into the service from day one.

Why Culver City, CA Homeowners Choose Us

We are the integrator-electrician: the only firm on your project that holds the C-10 and programs the Control4 or Josh AI system. That matters on a new build. When one contractor owns the line voltage, the structured wiring, and the programming, there is no gap between the panel schedule and the keypad layout, and no second company to coordinate at rough-in.

We sell whole systems and whole projects: new builds, full renovations, estate upgrades, and commercial build-outs. We do not run service calls. Specifiers work with us directly because we speak their language: amperage, load calculations, brand and model lines, how a scene is engineered, and what a 400A service makes possible for the rest of the design.

Aaron Buzo owns the firm and leads the work. Buzo Electric Co holds CSLB C-10 #1048529 and is bonded with workers' comp. Our shop sits at 2530 S Spaulding Ave in West Adams, beside Culver City, which keeps us close to the job site through every phase of the build.

Serving Culver City, CA and Nearby Areas

Culver City sits beside our shop, and our project footprint covers the west side of Los Angeles County. Beyond Culver City, we take on new builds and full renovations in Los Angeles, Beverly Hills, Santa Monica, Malibu, Pacific Palisades, Brentwood, Bel Air, West Hollywood, Marina del Rey, Venice, Calabasas, Hidden Hills, and Manhattan Beach.

New Construction Electrical Questions We Hear in Culver City, CA

Does a new custom home in Culver City need a 400A service?

It depends on the load calculation, which is where we start. A home with EV charging, a Generac standby generator, electric cooking, and a full AV head end often exceeds what a 200A service supports. We run the numbers during design-build and size the service, panels, and subpanels before plans go to permit.

Can one firm handle both the electrical and the automation?

Yes, and that is the point of our model. We hold the C-10, pull the structured wiring at rough-in, build the rack, and program the Control4 or Josh AI system ourselves. Your GC coordinates one contractor for line voltage, low voltage, lighting control, and AV instead of three.

We are rebuilding an older Culver City property. Does that change the electrical scope?

Often, yes. The typical Culver City home was built around 1963, per U.S. Census Bureau ACS estimates, and a full renovation of a home from that era usually means a complete service upgrade, new panels, and new wiring throughout. Owners rebuilding here generally plan for modern capacity: a 200A or 400A service, a Span smart panel, EV charging, and standby power engineered in from the start.

When should the electrical contractor join the project?

At design, before plans are final. Keypad locations, shade pockets, rack placement, generator pad, and service sizing all affect the architecture. When we join at design-build, the load calculation and the lighting control plan are in the drawings, and rough-in proceeds without change orders driven by late decisions.

Get Started

If you are planning new construction electrical in Culver City, CA, send us the plans or a project summary and we will walk the scope with you: service size, panel layout, lighting control, structured wiring, standby power, and the integration package. We review the drawings, flag what the design needs electrically, and return a defined scope you and your architect or GC can build against. Contact us to start the conversation while the project is still on paper; that is when the electrical plan does the most for the build.

Prefer to talk it through? Call (323) 252-7498 — a quick call is usually the fastest way to get a straight answer for your situation.